General Purpose Epoxy
MAX GPE A/B MEDIUM SET is a two-component epoxy based resin system designed to provide a broad range of mechanical and physical properties that is suitable for almost all types of epoxy resin applications. It can be utilized as a structural adhesive demonstrating excellent adhesion to wide selection of substrates, chemical resistant or protective coating, impregnating and laminating for composite applications, potting applications for electronics and as a casting resin for large and small applications.
For ordering and inquiries please call 877-403-8008.
Or visit our eBay Store, PolymerProducts.
Available Kit Sizes:
Description
MAX GPE A/B MEDIUM SET is mixed two parts Resin to one part Curing Agent by weight or by volume (2:1). The mixed consistency is very low in viscosity, clear and easily poured or applied in to place resulting in bubble free castings. MAX GPE A/B MEDIUM SET has a 60 minutes gel time that allows adequate working time for casting, coating, bonding and potting or encapsulating applications.
MAX GPE A/B MEDIUM SET performs well as an adhesive for metals, alloys, plastic, wood, stones products, fiberglass, carbon fiber composites and concrete and other substrates that require high tensile shear strength properties. Higher adhesion performance can be achieved after a post cure cycle of 1 hour at 120oC.
MAX GPE A/B MEDIUM SET coating properties exhibits very high gloss, good color stability, high surface and excellent chemical resistance.
Optimized amounts UV inhibitors, anti-oxidants and stabilizers are incorporated with the MAX GPE A/B MEDIUM SET to provide added outdoor durability.
An aliphatic polyurethane coating should be applied to further improved resistance to UV degradation.
MAX GPE A/B MEDIUM SET can be used as a protective or decorative coating for metals, alloys, plastic, wood, stones products, fiberglass, carbon fiber composites and concrete and other substrates
Higher coating performance can be achieved after a post cure cycle of 1 hour at 120oC.
MAX GPE A/B MEDIUM SET is an excellent choice for composite fabrication using fiberglass, carbon fiber, Aramid, and other hybrid fabrics. Its low viscosity allows fast fabric wet-out resulting in minimal void and laminant porosity. Cured composites fabricated with
MAX GPE A/B MEDIUM SET exhibits exceptional mechanical properties such as impact resistance, compressive and tensile strength. Higher mechanical performance can be achieved after a post cure cycle of 1 hour at 120oC.
As a casting resin and potting compound, MAX GPE A/B MEDIUM SET demonstrates good dimensional stability excellent electrical insulative performance and low coefficient of expansion and contraction.
General mechanical properties are enhanced after a post cure cycle of 1 hour at 120oC.
Physical and Mechanical Properties
Physical Properties
Viscosity | 900 cPs Mixed |
Mix Ratio | 100 parts A to 50 parts B by weight or volume |
Working Time | 65 Minutes at 200 Gram Mass |
Peak Exotherm | 160oC |
Time To Reach Peak | 80 Minutes |
Density | 1.10 g/cc Cured |
Cure Time | 1 to 3 days at 25oC |
Heat Cure | 2 Hours @ 25oC Plus 1 Hour @ 120oC |
Set-To-Dry @ 10 Mil Film | 6 Hours |
Surface Dry | 9 Hours |
Handling Time | 8 Hours |
Mechanical Properties (1)
Test Criteria | Room Temp Cure | Room Temp + Heat Cure |
Hardness | 78 D | 81 D |
Izod Impact ft-lb/in | .13 | .19 |
Tensile Shear Strength psi | 3,100 | 3,765 |
Tensile Strength psi | 9,600 | 12,300 |
Tensile Modulus psi | 460,000 | 489,120 |
Ultimate Elongation % | 3.8 | 2.3 |
Heat Distortion Temperature | 84oC | 110oC |
Compressive Strength | 12,300 | 13,000 |
24 Hours Water Boil% Weight Gain | 2.2 | 1.8 |
Electrical Properties (1)
@ 23oC | @ 40oC | @ 60oC | @ 100oC | |
Dielectric Constant 100 HzASTM D-150 | 4.7 | 4.7 | 4.7 | 5.4 |
Dissipation Factor 100Hz | 3.4 x 10-3 | 3.1 x 10-3 | 3.5 x 10-3 | 6.9 x 10-3 |
Volume ResistivityOhm-cm | 5.0 x 1015 | 3.4 x 1015 | 2.6 x 1014 | 2.4 x 1014 |
Dielectric Strength V/mil | 1/8 Inch Thick558 |
(1) Cured 2 hours at 80oC plus 3 hours 125oC